Baja blaster 65 torque converter

Free Shipping. Add To Cart. Fuel Tank for 5. This torque converter driver clutch is what is known as a Series 30 clutch assembly. A Series 30 clutch may be discerned from the very similar Series 20 by its asymmetrical pulley. The sliding sheave will be conical while the stationary sheave will be almost flat in comparison. On a Series 20 pulley, the two sheaves will both be angled. Detailed Installation Instructions included. Users have been able to use a lug nut to install the Driver Clutch on this engine.

Has the proper throttle cable linkage needed for a minibike. GTC Website. The performance impressed our technicians. The low end power and torque was strong enough to raise the front wheel with just barely applying the throttle. Take off and acceleration was also remarkably impressive. Taking on a steep hill from a complete stop, the TC2 smoothly down shifted and pulled the pound rider up the hill with ease. On level ground, at maximum throttle, the TC2 shifted into a very high overdrive ratio and gave us an impressive top speed of 52mph from this stock 5hp Tecumseh.

The TC2 Torque Converter is a complete kit that includes both drive and driven clutches, belt, billet aluminum engine mounting plate with a built in jackshaft and sprocket, all hardware and installation instructions. TC2 Bolts onto most engines with a horizontal shaft including:. High Performance.

The TC2 is a High Performance asymmetrical torque converter system in which the sheave faces have different angles. The system operates with the torque sensing cam in an outboard position allowing for in-line operation of the unit.

The primary benefit of this design is that it allows proper alignment of the final drive chain to be on the same side of the vehicle as the torque converter.

Moreover, the angle on the movable sheave being set at 18 degrees enables the unit to raise the belt to a larger pitch diameter with less travel of the sheave. This allows the unit to achieve higher overdrive ratios at maximum RPM. TC2 Drive and Driven Units. Children under the age of 16 should not operate vehicles with this product installed.

Do not operate the TC2 without a cover, chain and belt guard device designed specifically for your vehicle not supplied. Long hair or loose clothing can become entangled with moving parts and cause serious injury or death. Engines and moving parts can become hot and cause burns. By ordering this product, the purchaser accepts all risks associated with installation and operation of this product. If you ordered your Vehicle from us, we can look-up your records.

Product Reviews Login to rate or review this product See all reviews for this product. I'm new to this so I thought this wouldn't be bad, and it wasnt. The only problem was modifying parts and aligning the belt that wouldn't align properly with the parts given in the kit.

Also the chain wouldn't fit without 2 masterlinks and the keys would fit into the jack shaft without the use of a hammer and wd40 Aside from these annoyances, it's a mighty piece of machinery that'll make your bike much more powerful This is just a kit.

If you want the lug nut for the later models it is extra. The bad thing about it it's the wrong lug nut. Should be 1 to 1. If you put too much air into the tire, may burst, and causing severe injury. Check the air pressure from time to time while inflating the tire gradually, until the specified air pressure is obtained. Inspect the rear disk brake caliper for leakage. If brake fluid leaks, the safety of riding could be affected.

Inspect the brake hose for cracks, and the joints for leakage. Check the brake fluid level in the brake fluid reservoir, if level is at or below the LOWER mark, inspect brake pads for wear and hydraulic system for leaks. Readjust if it has more than 1. Adjusting the Chain To Tighten Chain: 1. Loosen all four bolts under engine mount plate. Slide engine back until chain is adjusted to the desired tension 0.

Remove the spark plug and reattach it to the spark plug lead. Apply the brake pedal to make sure the rear wheels are locked. If the ignition system is operating properly, a blue spark should jump across the spark plug gap. If there is no spark, take your machine to your service center. Drain screw Before transporting the Go-kart drain the fuel from the carburetor as follows: 1. Drain fuel from carburetor into an empty container by loosening the carburetor drain screw located on bottom of carburetor.

It will help keep your Go-kart looking and performing best. Proper cleaning can also extend the life of your Go-kart. It is important to clean and inspect your Go-kart after every ride, especially if it is used in mud, brush, grass, water, salt water, or very dusty conditions The build-up of mud, brush, grass, etc.

For this reason, we recommend that you trust this maintenance work to your authorized service center. If you wish to service the machine for storage yourself, follow the general guidelines below: VEHICLE Place the vehicle on level ground and wash the entire vehicle.

See your authorized service center with any additional questions you may have. You also need these numbers to help your authorized service center or Baja Motorsports order parts. The Frame number is stamped on the frame on the passenger side front end. The engine number is located on the front of the engine housing, facing the seat.

Four stroke Displacement Fair Ln. Print page 1 Print document 44 pages. Rename the bookmark. Delete bookmark? Cancel Delete. Delete from my manuals?